|
|
 Temperature |
 |
Temperature Calibrators
|
|
|
 TEMPERATURE
CALIBRATORS
Fast, Easy-to-Use and Accurate!
The Tel-Tru Check-Temp Calibrator is a dry block temperature
calibrator that allows accurate verification of thermometer
accuracy at the temperature point critical to the users
actual application.
As part of your HACCP Program, use Tel-Tru
Check-Temp Calibrators to verify the accuracy of your food
service and laboratory thermometers. Environmental
Safety and Health Professionals, Quality Assurance Managers
and HACCP Coordinators in food processing and smoking, preparing
and cooking, holding and serving and cooling and storage
are using the Check-Temp Calibrator to verify the accuracy
of their dial and digital thermometers.
|
Check-Temp II M and Check-Temp 40 M multi-hole
Check-Temp Calibrators allow you to verify the accuracy of
dial thermometers and digital probes of all sizes. The multi
hole units fit probes up to .250", .125", .187" and .375"
diameter.
Multi-hole Check-Temp Calibrators--
use with thermometer probes of all sizes! |
 |
Note: Image above is an enlarged view of 4 holes |
RELIABLE
ACCURACY:
- Accuracy ±0.2°F.
- Each unit serialized
and certified traceable to NIST.
- Built in circuitry
to warn if unit is more than 1°F out of calibration.
- Optional factory
re-certification and maintenance program.
Simple
Set Up - Plug in and turn
it on!
Use
With Dial TypeThermometers - Built in tool for holding
the calibration nut makes adjustments FAST
and EASY.
Use
With Digital Thermometers - Compare actual performance
to accuracy specifications.
Temperature
Units - Check & calibrate
at your critical temperature point.
- Check-Temp
140°F - High temperature unit, fits probes up to .150"
diameter.
- Check-Temp
160°F - Temperature at which E. Coli and other pathogens
are killed. High temperature unit, fits probes up to .150"
diameter.
- Check-Temp
40°F M - Low temperature unit with four holes, fits
probes up to .250", .125", .187" and .375" diameter.
- Check-Temp
II M - Dual cold and hot (40°F and 160°F) unit with
four holes, fits probes up to .250",.125", .187" and .375"
diameter.
- Custom
hole diameters available--Consult M<esting.
- Custom temperature points available--Consult
M<esting.
| SPECIFICATIONS |
CHECK-TEMP
40 M
|
CHECK-TEMP
140
|
CHECK-TEMP
160
|
CHECK-TEMP
II M
|
| Setpoint |
40°F |
140°F |
160°F |
40°F
and 160°F |
| Accuracy |
±0.2°F |
±0.2°F |
±0.2°F |
±0.2°F |
| Stability |
±0.09°F |
±0.06°F |
±0.06°F |
±0.07°F |
| Heating
Time |
Approx.
3 min. |
Approx.
8 min. |
Approx.
10 min. |
Approx.
3 min. |
| Fits
Probes Up To |
.250",
.125", .187"and .375" |
.150" |
.150" |
.250",
.125", .187" and .375" |
| Voltage |
90
to 130 VAC, 50/60 Hz |
90
to 130 VAC, 50/60 Hz |
90
to 130 VAC, 50/60 Hz |
90
to 130 VAC, 50/60 Hz |
| Power |
25
Watts |
45
Watts |
45
Watts |
25
Watts |
| Weight |
9.2
lbs. |
8.9
lbs. |
8.9
lbs. |
9.2
lbs. |
| Housing
Material |
Stainless
Steel 304SS |
Stainless
Steel 304SS |
Stainless
Steel 304SS |
Stainless
Steel 304SS |
| Size |
3-1/16"
H x 6-5/8" W x 10-7/8"D
(78 mm x 168 x 276 mm) |
3-1/16"
H x 6-5/8" W x 10-7/8"D
(78 mm x 168 x 276 mm) |
3-1/16"
H x 6-5/8" W x 10-7/8"D
(78 mm x 168 x 276 mm) |
3-1/16"
H x 6-5/8" W x 10-7/8"D
(78 mm x 168 x 276 mm) |
* HIGH TO LOW or LOW
TO HIGH takes approximately 5 minutes.
- Annual Re-certification
& Maintenance Notification Service
- Custom hole diameters
and temperature points available--Consult Factory
- Carrying Case -
Padded CORDURA® nylon
- Dial Adjustment
Tool - For 1" and 2" Thermometers
- Cleaning Brushes
- NEW--Tip
Sensitive Probe Adapter
|
TIP SENSITIVE PROBE ADAPTER
|
 |
|
Note: Calibrator
accuracy, with sleeve, is +/- 1%. |
Tip Sensitive
Probe Adapter:
The probe
adapter sleeve is to be used when calibrating electronic
probes. Fits into the 3/8" diameter hole of Check-Temp
40 M and Check-Temp II M. When adapter is used Check-Temp
accuracy is ±1%. Use with probes 3-3/8" minimum length
or greater and 3/16" maximum OD or smaller.P
|
|
|
M&L Testing Equipment
(1995) Inc.Canada, carries a large inventory of materials testing equipment.
If you have
any questions regarding a listed product, or if you do not see the equipment
you require, please contact us by using our Contact
Form or E-mail us @
.
A representative will contact you regarding your request shortly.
M&L Testing Equipment
(1995) Inc. ©1996-2007 - 31 Dundas St. (Hwy # 5) Dundas, Ontario,
Canada L9H 7H8
Tel: (905)
689-7327 Fax: (905) 689-3978 Toll Free: 1-800-263-9244
click for map & directions
Calgary Office: 4530-14th St. N.E., Calgary, Alberta Canada
T2E 6T7
Tel: (403) 250-6765 Fax: (403) 250-6803Toll Free: 1-800-663-4779
e-mail:
Site
Updated December 12, 2008
web design
by: Virtual
Image,
Dundas
|
|
