|
 Computorq
II ™ Digital
Electronic Torque Wrench
- Largest
Storage Capacity Available
Up
to 4000 torque values can be stored in memory. An audible
tone signals when memory is full.
- Down
Loading Capacity
Computorq
II is equipped to down-load individual torque values or
store values in memory which can be directly down-loaded
to a printer/computer or datalogger via RS232.
- Selectable
Modes of Operation
"Peak
Hold" and "Track" modes of operation are
standard. Computorq II's electronics are far superior
to our competitors in capturing real torque value in "Peak"
mode
- Easy
Set-Up
Target
torque values (high and low percentage, +/- tolerances
and torque engineering units) are easily programmed through
the keypad and shown on the LCD.
- Quality
Construction
Proven
industrial quality. Designed for continuous use.
- Range
Available
from 5 in. lb. to 1000 ft. lb.
- Batteries
A
9V alkaline battery is standard and provides enough power
for 60 hours of operation. A "LO BAT" indication
on the display signals for replacement.
- Accuracy
+/-
1% From 20-100% of scale
+/- 1%, plus 5 increments, from 10 -20% of scale
- Calibration
Data
All
calibration data is stored in the microprocessor
- Baud
Rate
The
baud rate for downloading to a printer/computer/data logger
is selectable. The factory set rate is 1200. Options are
300, 600, 1200 2400, 4800, 9600 or 19,200.
| PART
NUMBER |
DRIVE |
RANGE |
INCREMENTS |
LENGTH
IN. |
WEIGHT
LBS. |
| 501-C1-II |
1/4" |
5
- 50 in. lb.
5.6 - 56 dNm
5.7 - 57 cmkg
80 - 800 in.oz. |
.01
in. lb.
.01 dNm
.01 cmkg
.1 in. oz.
|
13.5" |
1.5" |
| 2502CI-II |
3/8" |
25-250
in. lb.
28 - 282 dNm
29 - 288 cmkg
|
.1
in. lb.
.1 dNm
.1 cmkg
|
14.9" |
2.0" |
| 502CF-II |
3/8" |
5
- 50 ft. lb.
68 - 667 dNm
69 - 691 cmkg
60 - 600 in. lb.
|
.01
ft. lb.
.1 dNm
.1 cmkg
.1 in. lb. |
14.9" |
2.0" |
| 2503CF-II |
1/2" |
25
- 250 ft. lb.
34 - 338 dNm
3.4 - 34 mkg
|
.1
ft. lb.
.1 Nm
.01 mkg
|
21.5" |
3.2" |
| 6004CF-II |
3/4" |
60
- 600 ft. lb.
81 - 813 Nm
8.3 - 83 mkg
|
.1
ft. lb.
.1 Nm
.01 mkg
|
46.5" |
9.5" |
| 10005CF-II |
1" |
100-1000
ft. lb.
135-1355 Nm
14 - 138 mkg
|
.1
ft. lb.
.1 Nm
.1 mkg
|
74.0" |
19.0" |
The
ranges listed above are for reference, as most of the torque
engineering units can be selected through the keypad (Ft.
Lb., In. Lb., In. Oz., NM, dNM, Mkg and cmkg).
CABLES:
P113-50 - TO 9 PIN P.C.
P113-60 - TO 25 PIN P.C.
Computorq-II
Audio/Visual Indicators
| KEY
PAD FUNCTIONS |
| A |
|
Analog
Bar Graph |
|
L |
|
Number
of Torque Values in Memory |
| B |
|
Super
Twist LCD |
|
M |
|
Low
Battery Indication |
| C |
|
7
Torque Units |
|
N |
|
Track
Mode |
| D |
|
Green
"Go" Limit LED |
|
O |
|
Peak
Hold Mode |
| E |
|
Power
On/Off |
|
P |
|
Red
"Over Torque" Limits LED |
| F |
|
Clear
LCD Display |
|
Q |
|
Scroll
Up |
| G |
|
Zero
Tare |
|
R |
|
Store
Data to Switch |
| H |
|
Enter |
|
S |
|
Send
Data to Computer/Data Logger/Printer |
| I |
|
Recall
Stored Torque Data |
|
T |
|
Shift
to Next Flashing Digit |
| J |
|
Over
Torque "Warning" |
|
U |
|
Set
Up Parameters |
| K |
|
Specific
Torque # in Memory |
|
V |
|
Audio
Buzzer |
Computorq
II wrenches are equipped with both audio and visual signals
in addition to the torque information supplied on the LCD.
- Audio
Signal
An
audio signal is emitted when the minimum acceptable standard
indicators of high and low preset torque value is reached
or the upper torque limit is exceeded.
- Visual
Indicators
Bright
green and red LED's are standard indicators of high and
low preset torque limits.
- Over-Load
Protection
The
red LED flashes, the audio buzzer sounds and "OVER"
is displayed on the LCD when the torque range of the wrench
is exceeded.
- Earpiece
Option
An
external jack for remote earpiece signaling in noisy working
environments is available as an option.
- New
Liquid Crystal Display
Large
sized Super Twist liquid crystal display incorporates
technology improving visibility of displayed data from
any viewing angle. The display is updated five times a
second for changes in torque measurements. There is no
perceived lag between applying torque and updating the
measurements on the LCD. It is the fastest on the market.
- Engineering
Units
All
seven basic engineering torque units are available on
most Computorq 11 models (Ft. Lb., In. Lb., In. Oz., Nm,
dNm, Mkg, or cmkg) and are easily selected through the
keypad.
- Displayed
Torque Measurements
Torque
measurements captured on the display remain until they
are erased, sent to the wrench's memory, or down-loaded
to an external device.
Keypad
- New
Embossing Membrane Keypad
This
new design gives positive touch and response when any
key is depressed. Depression of any key is acknowledged
by an audible signal giving a positive indication of acceptance.
Entire keypad is sealed against moisture and contaminants
- On/Off
Switch
There
is an On/OFF switch to conserve battery life located on
the side of the wrench.
- Sleep
Mode
After
a specified time period of inactivity, the wrench's display
switches into a "sleep mode". All memory is
retained while in the sleep mode. Operation may be continued
by pressing the keypad.
- Recall
of Torque Measurements
Up
to 999 torque measurements can be reviewed by the operator,
last in first displayed, by pressing the recall button.
- Recall
Display
When
the recalled torque measurement is displayed on the LCD,
the sequence number and total number or stored values
are also displayed for reference.
- Bar
Graph
A
bar graph is displayed on the LCD showing the relative
position of applied torque to the preset torque range.
In track mode, the bar graph displays the relative position
of the applied torque to the full range capability of
the wrench. The bar graph is updated 10 times per second.
- Directional
Indicators.
There
is a +/- indicator on the LCD showing clockwise or counter-clockwise
application of torque.
|
CDI
Computorq II ™ 
